Audi 80/Avant + Technical specification + Engines + System of production of the fulfilled gases + Cooling system + Fuel tank and fuel pump + Air filter and airintaking channels + System of injection + Coupling + Transmission and transmission + Suspension bracket and steering + Brake system + Anti-blocking system of brakes + Wheels and tires + Body electrical system + System of ignition + Lighting + Signalling devices + Devices and auxiliary devices + Heating and ventilation - Body elements Front bumpers Forward part of the car Cowl Wings Moldings Doors External rear-view mirrors Forward and back flew down Trunk lid at a sedan Back door of the versatile person Rear bumper Movable hatch Clearing of openings for a water drain Control of anticorrosive protection of the bottom of a body Salon Seats + Search of malfunctions + Specifications
|
Salon
Removal of the left shelf
|
For removal of a shelf to weaken bolts with 2 on 5 at the left. At installation to insert a shelf ahead in directing (the position 1 shows one of them). |
The left lower part of a covering of the dashboard integrated with a shelf has to be removed almost in all cases when access to a reverse side of the dashboard is necessary.
|
- Narrow face key to turn out four screws round a shelf.
- To cast away a little a shelf down and to extend to itself.
- At installation to insert a first line of a covering into both directing on the bottom of the car and near pedals.
- Not too hardly to tighten screws.
|
|
Removal of a ware box
|
The ware box (2 and 3) is attached by (1) loops to (arrow) dashboard. On an illustration the box is shown in unassembled form. |
|
- To turn out both fixing screws of a loop of a ware box at bottom edge of the dashboard.
- Slightly to wring out stoppers of a ware box inside and to cast away a ware box down.
|
|
Removal of the lower part of the central console
|
Removal of back part of the central console: to remove a level (1), to disconnect a covering of the lever of the parking brake (3), to disconnect an earring (arrows) on the handle (2) from a clamp. |
|
- To tighten the parking brake.
- To wring out a screw-driver fixing laying of a cover of the lever of the parking brake and to separate from a floor.
- In front slightly to raise a covering, to wring out a lever earring up and to extend the lever forward.
- To raise the decorative panel in front of the lever of the parking brake. Thus to hook the upper edge a small screw-driver.
- To turn out six fixing bolts which are under the panel.
- To remove a back ashtray.
- To turn out two six-sided bolts under an ashtray.
- To pull console part for a first line up and to remove it in the direction forward over the lever of the parking brake.
|
|
Removal of forward part of the central console
|
Removal of forward part of the central console: to turn off a head of the lever of gear shifting (2), to weaken a bolt on a casing of the lever (1). (3) – the lobbies directing. |
|
Shooters show on two bolts located in cut of the panel of heating which need to be weakened for removal of the central console. |
|
- To disconnect a wire on "mass" of the accumulator.
- Completely to remove back part of the central console.
- To remove the lever of gear shifting or the lever of the selector.
- To turn off a bolt with crosswise shliyets at back edge of the console and to remove a cover of the handle of gear shifting or a covering.
- To disconnect all three regulators of heating/ventilation.
- To unscrew two screws of the panel of heating and to remove it.
- At the cars equipped with the automatic conditioner completely to remove the control panel.
- Below on the right and at the left in cut of the panel of heating to turn out on one screw.
- To wring out the console with an ashtray down, at body option with additional devices to remove in the direction a narrow decorative plate down.
- In the direction to disconnect the console from a control panel back.
- If necessary to disconnect wires.
- At installation directing on the dashboard and the central console have to enter one another.
|
|
|
|