Audi 80/Avant (B4)

since 1991-1995 release

Repair and operation of the car



Audi 80/Avant
+ Technical specification
+ Engines
+ System of production of the fulfilled gases
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and airintaking channels
+ System of injection
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Anti-blocking system of brakes
+ Wheels and tires
+ Body electrical system
+ System of ignition
+ Lighting
+ Signalling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
   Front bumpers
   Forward part of the car
   Cowl
   Wings
   Moldings
   Doors
   External rear-view mirrors
   Forward and back flew down
   Trunk lid at a sedan
   Back door of the versatile person
   Rear bumper
   Movable hatch
   Clearing of openings for a water drain
   Control of anticorrosive protection of the bottom of a body
   Salon
   Seats
+ Search of malfunctions
+ Specifications





Trunk lid at a sedan

The lock and the castle drive in a cover of a luggage compartment of a sedan of Audi 80

1 – lock;
2 – the movable button of connecting draft between the lock and the press button;

3 – press button;
4 – connecting thirst for system of locks with the central management.

Removal

 PERFORMANCE ORDER

  1. To open a cover.
  2. To cast away a little a covering of a luggage compartment it is above the left back dimension.
  3. To separate shtekerny connection of wires to a cover of a luggage compartment and to pass plugs via the sealing plug in metal.
  4. If the car is equipped with system of locks with the central management, it is necessary to disconnect a hose to the lock drive at cover loops.
  5. On the right and at the left to cast away and remove lock brackets on pneumatic springs. After that it is possible to wring out pneumatic springs from spherical heads.
  6. Supporting a cover together, to turn out on the right and at the left two bolts in loops.
  7. To uncover loops.
  8. It is in addition possible to disconnect loops from a body.

Adjustment of a cover of a luggage compartment

Sedan

 PERFORMANCE ORDER

  1. It is necessary to achieve an identical gap between the right and left details of a body and a trunk lid (about 4 - 5 mm). Also near back glass the distance to a cover has to be identical on the right and at the left.
  2. It is necessary to regulate after weakening of fixing bolts of loops on a cover of a luggage compartment.
  3. Besides, the cover has to coincide on height with wings. It can achieve after weakening of fixing bolts of loops on a sidewall.
  4. If the trunk lid knocks or is badly closed, it is possible to adjust the lock buffer on the right and at the left above on lateral part.
  5. To weaken and shift up or down a fixing bolt, then to tighten again. The lock buffer is installed correctly if it without tension adjoins to the closed cover.
  6. To check landing and closing of a cover of a luggage compartment, if necessary to otyustirovat a locking plate of the lock of a luggage carrier.
  7. The block of headlights in a cover has to defend from headlights in lateral part approximately on 8 mm. It can be reached by moving of the block of headlights in their longitudinal openings.

Removal of the lock of a luggage carrier

Sedan

 PERFORMANCE ORDER

  1. To open a cover of a luggage compartment.
  2. To remove an internal covering under the press button of the lock of a luggage carrier.
  3. Removal of the button: to take aside a lock bracket on driving draft and to remove draft.
  4. To disconnect shtekerny connections for the microswitch of system of locks with the central management.
  5. To turn out two nuts, to remove in the direction inside the press button with lock cylinders.
  6. Removal of castle part: to disconnect driving drafts from the press button (to take aside a lock bracket), to separate shtekerny connection.
  7. To turn out two six-sided nuts from below on the lock. To take out the lock in the direction down.
  8. At installation of a castle element to adjust length of driving thirsts for the press button.
  9. To shift the movable button in the middle of connecting draft back so that halves of draft were freely inserted each other.
  10. At an open trunk lid to put a lock latch to situation "is closed".
  11. To insert a six-millimetric drill into an opening of a castle element to record a latch.
  12. In this situation to record one in other carving sites of halves of draft and to stop the movable button.
  13. To remove a drill.